14MZ MANUAL PDF
February 12, 2021 | by admin
14mz, Instruction manual • Read online or download PDF • Futaba 14MZ User Manual. Get Futaba 14MZ Manual. Get all Futaba manuals! 14MZ. 14 CHANNEL RADIO CONTROL SYSTEM. PCMG3/PCM/FM selectable. INSTRUCTION. Compact Flash (CF) Card Handling Instructions Follow these precautions when handling the CF card included in your 14MZ transmitter. DO NOT allow the.
|Country:||Saint Kitts and Nevis|
|Published (Last):||2 April 2013|
|PDF File Size:||8.95 Mb|
|ePub File Size:||6.92 Mb|
|Price:||Free* [*Free Regsitration Required]|
Close and lock the battery cover until you hear a snapping sound. When the charge-lamp turns off, charging has been completed. Mannual setting resets the data set by mixing function, etc.
Modification, adjustment, and replacement of parts: Each lever has two ends, one in front and the other on the back. You can listen to them through the built-in speaker or a headphone by the earphone plug. Replaceable switches You can replace 8 of the toggle switches on the right and left shoulder, with optional switches two position, three position, and momentary etc.
Turn off the power to the transmitter. When memory This function is used when you want to mix operation switch operation is performed with elevator operation with rudder operation. When you do not want to use the Condition Select function, this setting is unnecessary. Airbrake [Corresponding model type]: If you have purchased this product from an exporter outside your own country and not the authorized Futaba dis- tributor in your country, please contact the seller immediately to determine if such export regulations have been met.
FUTABA 14MZ INSTRUCTION MANUAL Pdf Download.
That rate is automatically assigned to that function. Its frequency can be changed within the range of the frequency band of the module used. Adjust the LCD contrast with the left and right side buttons.
If this product is then re-exported to other countries, it may be subject to restrictions on such export.
Remove the battery from the charger and remove the charger from the wall socket. Condition Select Condition Select Flight conditions addition, deletion, copy, condition renaming, and condition delay can be set. Open the dust protection cap on the back of the transmitter that is covering the hole for throttle stick adjustment. Up to 10 mixings can be used for each condition. If you do not find the answers to your questions there, please see the end of our F.
Perform this setting when you purchase the set and when adjustment is necessary. It will take about 30 seconds to be ready for use, as it takes time to initialize the internal circuit of the transmitter. It is used correction rudder applied in the Memory Mode, to correct undesirable tendencies when rudder is the stick position at that time is displayed on the applied in roll maneuvers, knife edge, etc.
Remember that up to 30 model memories are available in the transmitter; these may be stored in the CFDP32M card. Rates are adjusted separately.
Flap setting [Corresponding model type]: Push the area of the user’s name shown on the home screen or the “user’s name” in the linkage menu. A photograph of the model taken with a digital When a picture is pasted, it is displayed as the camera or other file can be pasted as the screen following screen image: Then turn off the power of the transmitter following the instructions shown on the screen. When transmitter power switch turned off No. Be sure to keep the backup of your important data in your CF card.
V-tail [Corresponding model type]: Select the range of the frequency band of the module used. Move the slide lever to the far right. Use the attached jig inside stylus to turn the Outside levers face nuts counterclockwise, this will detach the switches. Adjustment of Stick Lever Tension You can adjust the tension of stick-levers.
Receiver and servos connection – Futaba 14MZ User Manual
If you do this you will make it on your on risk. Its memory size is 32MB. Sounds recorded with the microphone built into the transmitter and audio files. Manjal the LCD contrast with the left and right side buttons.
If you remove this you must calibrate the throttle stick. Page 99 Gyro [Corresponding model type]: The trim positions you have set will be stored in the non-volatile memory and will remain there. Mahual 31 Trainer Trainer system starting and setting The Trainer function makes it possible for the instructor to choose which functions and channels are to be used for instruction, making it possible to match the training ability to the student’s skill level.
Condition delay setting 1.
Turn on your receiver power. Add conditions, as required.
Idle down – Futaba 14MZ User Manual
Page 32 Student mode to confirm this after connecting your trainer 1. Up to 6 dual rates can be set for each condition. The Model Select function of the Linkage Menu is used to add models and to call models which are already set.
Page 68 Mixing Rate Linkage Compensation This compensation mixing is used to correct 41mz This compensation mixing is used to correct the tendency of the swash-plate for each control near tendency of the swash-plate for pitch control at low the hovering point. The indicators on 1mz screen display actual servo throw of the each channel.