May 14, 2021   |   by admin

CDB CMOS stage Ripple-carry Binary Counter/divider And Oscillator Data sheet acquired from Harris Semiconductor SCHSB Revised March . 3. Ordering information. HEFB. stage ripple-carry binary counter/divider and oscillator. Rev. 8 — 25 March Product data sheet. Table 1. Ordering. December CDBMS. CMOS 14 Stage Ripple-Carry Binary Counter/ Divider and Oscillator. DATASHEET. Pinout. Functional Diagram.

Author: Mubei Mektilar
Country: Switzerland
Language: English (Spanish)
Genre: Life
Published (Last): 20 June 2006
Pages: 177
PDF File Size: 2.12 Mb
ePub File Size: 11.34 Mb
ISBN: 219-9-18022-975-2
Downloads: 46307
Price: Free* [*Free Regsitration Required]
Uploader: Tugor

Did you connect the anode to Q8 and the cathode to the Reset input, then add a k resistor from reset to ground so that the ‘ doesn’t stay in reset all the time? The Infrared Interferometer, Spectrometer, and Radio Astronomy of the Voyager Spacecraft This article in our Voyager series looks at datasheet, ultraviolet, and radio science experiments on the Voyager spacecraft. Customers are responsible for. Hi all, What is the maximum periodic time I can get at pin 7 Q3? Oct 25, 4. Your name or email address: That is an extremely high resistor value, and is based on the input stage device physics.

If it is too small a few KOhms the output of the inverter has trouble driving it. TI does not warrant or represent that any dstasheet, either express or implied, is granted under any TI patent right. For example, the datasheet extract above indicates a max timing resistor of 20 M. The state of the counter is advanced one step.


Oct 25, 7. Body dimensions do not include mold flash or protrusion, not to exceed 0. Unfortunately it did not work when datashdet the attached schematic.

The Inverting Configuration of an Amplifier Mentioned in the previous article, an operational amplifier is usually connected to components in a feedback circuit. From the calculations I made, the output at Q4 should have a periodic time of s. Oct 25, 8. Max Cx and Rx is supply voltage dependent but its on the TI datasheet.

GopherT do you mean pin 14 rather than pin datawheet Believe everything you read. All linear dimensions are in millimeters. It does not account for any leakage current around the input fd4060b due to dust and finger oil and other contaminants on the chip and the pc board, and it makes for a very high circuit impedance that is more susceptible to external noise.

(PDF) CD4060B Datasheet download

Following are URLs where you can obtain information on other Texas Instruments datzsheet and application. Oct 25, Oct 25, 3. For instance, I need to pause the circuit when Q8 turns high. Customers should obtain the latest relevant information before placing. All inputs and outputs are fully. Generally, 10k to a few hundred k keeps life simple.

Data sheet acquired from Harris Semiconductor. All products are sold subject to TI’s terms. You need at least some steering diodes, and possibly a gate between the output and the oscillator input or enable input. Jun 8, 1, Datasheeg and other quality control techniques are used to the extent TI.


And to a previous point, not only is much innergoogle information unreliable, some of it is technically correct but incomplete without some experiencee or guidance. RESET line accomplishes the reset function. Nov 23, 8, 6, So 1 M is a common practical upper limit for the timing resistor, maybe more datasheeh controlled conditions.

H CDB consists of an oscillator. Except where mandated by government requirements, testing of all.

CDB Datasheet(PDF) – TI store

Mar 30, 7, 1, The resistor can vary over a wide range. By the way, I hope all understand that though power supply decoupling capacitors are not shown on any of the schematics thus far, they should be present in the physical circuit.

All linear dimensions are in inches millimeters. Oct 25, 1. Oct 26, No, create an account now. Oct 25, 9.

Posted by PauloConstantino in forum: Sep 21, 6. I have another quick question. I’ve never seen or heard of success at or above 10 M. Since I already had the components for the available, I decided to build it on a protoboard. In this article, we will discuss one of two amp configurations that are most widely used.

I did try to connect a diode from Q8 to pin 11, but it did not work as expected. Oct 27,